Assembly instructions | Repetier Host

Step 0

Damit wir die Drucker schneller verschicken können, wurde die Slider für XYZ noch nicht angepasst. Dafür liegt aber PTFE Spray bei. Die Anpassung dauert circa 5-10Minuten pro Slider. Dazu das Aluprofil ein den Slider schieben, einmal auf der Rückseite des Sliders leicht ein zwei Mal draufklopfen. Das Aluprofil wieder rausziehen und den Vorgang wiederholen. :) Damit beim Z Slider (der mit der Motorhalterung) nichts abbricht bitte nicht an den Halterungen ziehen sondern direkt an der Einführung für das Aluprofil. Wenn es sich die Slider gut hin und her schieben lässt, etwas PTFE Spray auf das Aluprofil und in den Slider sprühen. Dann draufschieben und nochmal 1-2Minuten schnell hin und her ziehen. Fertig.

Step 1


Take 4x M4 10mm Screws, 4x M4 Hammer Nut and the plate.


Now fixate the Alu Profiles on the plate.


Your Hammer Nut must rotate 90 degrees.


Use 4x M4 8mm Screws, 4x M4 Hammer Nut and 2x Fitting Angle.


Connect the Alu Profiles with the Fitting Angles.

Step 2


Connect the 3x M4 10mm screws on the plastic part.


After that, slide it into the Alu Profile and thighten the screws.

Step 3


The same, first connect the screws on the plastic part.


After that, slide the Alu Profile from top and thighten the screws. Now fixate the Fitting Angle.

Step 4


Loosely screw the nut onto the front plastic parts.



Step 5


Fixate the handle on the Z axis Alu Profile.

Step 6


Connect the stepper holder at the back of the plate and the ramps case in front.

Step 7



Step 8


Put the nema 17 stepper into the holder. Now fixate the pneumatic connector with the plastic part.
After that, use 2x M3 30mm screws for the sockel (left side) and 2x M3 12mm screws for the right side.
Dont forget the extruder gear and fixate it.


Now use the M4 8mm screw to connect the extruder bearing. The M3 12mm screw must into the plastic part.
Fixate the plastic part with a M3 20mm screw and use the spring between the plastic parts.

Step 9


You must fixate the Nema 17 stepper on the Z Axis Alu Profile.



Step 10


Put the M8 Nut into the plastic part and fixate it on the z axis plastic part with the M3 30mm screws.


Please push the rod is not completely pure.

Step 11



Step 12



You must fixate the Alu Profile 27cm (X Axis) on the XZ plastic part.

Step 13













Step 14









Step 15





Step 16







Step 17









Step 18


You only need 20-25cm long cables. Measure rough and cut of.


Turn the cable into each other or solder it.

Step 19


Cut the plug off

Step 20





Step 21


You only need a 60cm long bowden tube. Connect it into the pneumatic connectors.

Step 22













Step 23


Now connect the pins and cables.

Step 24





Step 25


Push the screw all the way down and fixate it. Use two nuts for the endstop.





Step 26





Step 27





Step 28





Step 29




Attention!!! Red cable -> Ramps + to DC connector +, Black cableto Ramps - -> DC connector -

Step 30


Install Arduino IDE and open the Marlin.ino from our TekBOT firmware. Now connect your 3D Printer to your PC (no Power cable only USB). Check your Arduino Settings (Board Arduino Mega, USB Port: XXX) and click on compile and upload.

Finish :)